Convert a Freezer Into Built In Kegerator Fridge

Oct 10th

Built in kegerator – To make a built-in barrel refrigerator, or “kegerator”, out of the freezer, you must first convert it to a refrigerator. Simply follow some basic steps to build your own barrel fridge. Instructions is, covert Freezer for refrigerator: Please locate the connector with three pins on the temperature controller. Plug it into a wall outlet near the freezer. Insert the temperature control plug into the freezer power cord. Set the temperature regulator sensor around or through the door seal the freezer. Set the temperature of 36 to 40 degrees Fahrenheit.

What Built In Kegerator Is
What Built In Kegerator Is

Fit the parts. Drill a 1, 15/16 or 7/8 inch hole in the side wall or die of the converted freezer into built in kegerator fridge. Insert the shaft into the hole from the outside and fasten it with a lock nut. Attach to the handle of the crane head. Insert a rubber disc into the lock nut. Add another lock nut to the other side of a beer line jumper. Place a rubber disc here too. Attach hexagon nuts to barrel clutch top and shaft is back. Hold the air conduit, mount one end of the nipple of the barrel connector. Attach thread with screwdriver. Take the air line’s other end and press over the nipple regulator. Attach the airline with a screwdriver.

25 Photos Gallery of: Convert a Freezer Into Built In Kegerator Fridge

Image of: What Built In Kegerator Is
Image of: Wet Bar Built In Kegerator
Image of: Undercouter Built In Kegerator
Image of: Triple Tap Built In Kegerator
Image of: Summit Built In Kegerator
Image of: Stainless Built In Kegerator
Image of: Single Tap Built In Kegerator
Image of: Patio Built In Kegerator
Image of: Outside Built In Kegerator
Image of: Outdoor Built In Kegerator
Image of: Oak Park Built In Kegerator
Image of: Laundry Room Built In Kegerator
Image of: Exiting Desk Built In Kegerator
Image of: Dual Tap Built In Kegerator
Image of: Custom Built In Kegerator
Image of: Chic Built In Kegerator
Image of: Caffee Built In Kegerator
Image of: Built In Kegerator Work
Image of: Built In Kegerator in Kitchen
Image of: Built In Kegerator Guide
Image of: Built In Kegerator Cover
Image of: Built In Kegerator Tap Tower Cover
Image of: Built In Kegerator Final
Image of: Built Built In Kegerator
Image of: 2017 Built In Kegerator
 

Install Gas Regulator; Let your bar rest several hours. Place a disc in the clutch nut, which is attached to the regulator. Screw the nut to the valve outlet of the cylinder and tighten it with a wrench. Turn off the shut-off valve. Open the drum cylinder valve. Turn the adjusting screw clockwise until the meter shows the correct pressure. Attach to barrel to barrel clutch. Open the valve on the tank of CO2. Put the shut-off valve handle on the regulator in the open position. Hint; clean the built-in keg system on a regular basis. Use a particular cleaning kit that contains chemicals made for barrel parts. Meanwhile, how to connect a built in kegerator? Connect CO2 into the barrel. First, connect the CO2 regulator to the actual aquarium CO2.

This will control how much CO2 is to be delivered to the barrel. (Depending on the type and amount of beer, this will vary. Read the instructions on the barrel to determine how much CO2 is going to be used.) Connect the controller to the CO2 line. A plastic pipe that sends CO2 into the barrel. Connect the other end of the line into the input valve in the barrel. Drop the barrel. Do put the keg into the actual keg, which will lie on the barrel. Run the beer line from the keg press to the beer faucet where you want to feed beer. Place the barrel in the refrigerator and close the door. This will keep the barrel chilled while in use. To pour a test glass of beer, open the beer faucet. And the built in kegerator was connect now.

RELATED TOPIC:   Ideas for Build Outdoor Grill Islands